192.168.2.41 255.255.255.0 按地址顺序排列的信号 　　　PLC----------->NC 　　EMERGENCY STOP 急停 DB10.DBX56.1 ; ACKNOWL EMERGENCY STOP 确认急停 DB10.DBX56.2 ; INC INPUT IN MODE 在状态组范围 GROUP AREA ACTIVE 起动增量输入 DB10.DBB57.0 ; NC----------->PLC HANDWHEEL 1 MOVED 手轮 1的移动量 DB10.DBB68 ; HANDWHEEL 2 MOVED 手轮 2的移动量 DB10.DBB69 ; HANDWHEEL 3 MOVED 手轮 3的移动量 DB10.DBB70 ; 手轮若干信号 DB10.DBB97 ; . . . DB10.DBB102 ; MMC TEMPERATURE MMC 温度极限 DB10.DBX103.6 ; MMC 101/102 MMC 电池报警 DB10.DBX103.7 ; NCK CPU READY NCK 准备 DB10.DBB104.7 ; EMERGENCY STOP ACTIVE NC 在急停状态 DB10.DBB106.1 ; INCH SYSTEM 英制系统 DB10.DBB107.7 ; MMC CPU READY MMC CPU 准备 DB10.DBB108.2 ; 3 ; DRIVE READY 驱动准备 DB10.DBB108.6 ; NC READY NC 准备 DB10.DBB108.7 ; NCK ALARM PRESENT NCK 报警出现 DB10.DBB109.1 ; HEAT SINK TEMP 热交换器温度报警 DB10.DBB109.5 ; AIR TEMP ALARM 气温过热报警 DB10.DBB109.6 ; NCK BATTERY ALARM NCK 电池报警 DB10.DBB109.7 ; ======================================================================== PLC------------>NC (给状态组1的信号) OPERATING MODE AUTOMATIC 自动状态 DB11.DBB0.0 ; MDA 手动输入状态 DB11.DBB0.1 ; JOG 点动状态 DB11.DBB0.2 ; MODE CHANGE DISABLE 禁止状态改变 DB11.DBB0.4 ; MODE GROUP STOP 状态组停止 DB11.DBB0.5 ; MODE GROUP STOP AXIS+SPINDLE DB11.DBB0.6 ; MODE GROUP RESET 状态组复位 DB11.DBB0.7 ; MACHINE FUNCTION TEACH IN 示教状态 DB11.DBB1.0 ; REPOS 再定位状态 DB11.DBB1.1 ; REF DB11.DBB1.2 ; SINGLE BLOCK A,B TYPE 单段 A,B 型 DB11.DBB1.6 ; DB11.DBB1.7 ; INC 1 增量 X1 DB11.DBB2.0 ; INC 10 增量 X10 DB11.DBB2.1 ; INC 100 增量 X100 DB11.DBB2.2 ; INC 1000 增量 X1000 DB11.DBB2.3 ; INC 10000 增量 X10000 DB11.DBB2.4 ; VAR.INC DB11.DBB2.5 ; NCK------------>PLC (来自状态组1的信号) STROBE MODE AUTOMATIC 自动状态 DB11.DBB4.0 ;MMC-->PLC MDA 手动输入状态 DB11.DBB4.1 ;MMC-->PLC JOG 点动状态 DB11.DBB4.2 ;MMC-->PLC STROBE MACHINE FUNCTION TEACH IN 示教状态 DB11.DBB5.0 ;MMC-->PLC REPOS 再定位状态 DB11.DBB5.1 ;MMC-->PLC REF DB11.DBB5.2 ;MMC-->PLC ACTIVE OPERATING MODE AUTOMATIC 自动状态 DB11.DBB6.0 ; MDA 手动输入状态 DB11.DBB6.1 ; JOG 点动状态 DB11.DBB6.2 ; MODE GROUP READY 状态组准备 DB11.DBB6.3 ; ALL CHANNELS IN RESET STATE 所有通道在复位 DB11.DBB6.7 ; ACTIVE MACHINE FUNCTION TEACH IN 示教状态 DB11.DBB7.0 ; REPOS 再定位状态 DB11.DBB7.1 ; REF DB11.DBB7.2 ; -------------------------------------------------------------------------------- NCK------------>PLC (来自状态组2的信号) DB11.DBB20 ; . DBB0--7 为通道1 . ; DBB20--27 为通道2 . DB11.DBB27 ; ================================================================================ DB12 对应 通道 3，4 ================================================================================ DB13 对应 通道 5，6 ================================================================================ DB14 对应 通道 7，8 ================================================================================ PLC----------->MMC SCREEN BRIGHT 屏幕亮 DB19.DBB0.0 ; SCREEN DARKENING 屏幕暗 DB19.DBB0.1 ; KEY DISABLE 取消钥匙保护 DB19.DBB0.2 ; CLEAR CANCEL ALARM 清除取消报警 DB19.DBB0.3 ; CLEAR RECALL ALARM DB19.DBB0.4 ; ACTUAL VALUE IN WCS/MCS 两个座标系切换 DB19.DBB0.7 ; 略略略略略略略略略 =============================================================================== DB20 PLC------>OPERATOR 略 =============================================================================== PLC------------>NCK DB21--->DB30 EXECUTION FROM EXTERNAL SOURCE 从外部执行 DB21.DBB0.0 ; ACTIVATE DRF 激活 DRF DB21.DBB0.3 ; ACTIVATE SINGLE BLOCK 激活单段 DB21.DBB0.4 ; ACTIVATE M01 激活 M01 DB21.DBB0.5 ; ACTIVATE DRY RUN FEEDRATE 激活空运转进给率 DB21.DBB0.6 ; ACTIVATE REFERENCING 激活基准功能 DB21.DBB1.0 ; ENABLE PROTECTION ZONE 使能保护区 DB21.DBB1.1 ; FEEDRATE OVERRIDE 进给率修调 DB21.DBB4 ; RAPID TRAVERSE OVERRIDE 快移率修调 DB21.DBB5 ; FEED DISABLE 进给禁止 DB21.DBB6.0 ; READ IN DISABLE 读入禁止 DB21.DBB6.1 ; DELETE DISTANCE TO GO 删除剩余距离 DB21.DBB6.2 ; RAPID TRAVERSE OVERRIDE ACTIVE 激活快移修调 DB21.DBB6.6 ; FEEDRATE OVERRIDE ACTIVE 激活进给修调 DB21.DBB6.7 ; NC STSRT DISABLE 禁止NC 起动 DB21.DBB7.0 ; NC START NC 起动 DB21.DBB7.1 ; NC STOP NC 停止 DB21.DBB7.3 ; NC STOP AXES PLUS SPINDLE NC停止轴和主轴 DB21.DBB7.4 ; RESET 复位 DB21.DBB7.7 ; -------------------------------------------------------------------- 对几何轴的控制信号 几何轴 1 ACTIVATE HANDWHEEL 激活手轮 DB21.DBB12.0,1 ; FEED STOP 进给停止 DB21.DBB12.3 ; TRAVERSING KEY DISABLE 禁止移动键 DB21.DBB12.4 ; RAPID TRAVERSE OVERRIDE 快移修调 DB21.DBB12.5 ; TRAVERSE KEY - 负向点动键 DB21.DBB12.6 ; TRAVERSE KEY + 正向点动键 DB21.DBB12.7 ; INC 1 增量 1 DB21.DBB13.0 ; INC 10 增量 10 DB21.DBB13.1 ; INC 100 增量 100 DB21.DBB13.2 ; INC 1000 增量 1000 DB21.DBB13.3 ; INC 10000 增量 10000 DB21.DBB13.4 ; VAR INC 可变增量变 DB21.DBB13.5 ; 几何轴 2 DB21.DBB16 ; DB21.DBB17 ; 几何轴 3 DB21.DBB20 ; DB21.DBB21 ; ----------------------------------------------------------------- MMC-------->PLC EXECUTION FROM EXTERNAL SOURCE SELECTED 选择了从外部执行 DB21.DBB24.0 ; DRF SELECTED 选择了 DRF DB21.DBB24.3 ; SINGLE BLOCK SELECTED 选择了单段 DB21.DBB24.4 ; M01 SELECTED 选择了 M01 DB21.DBB24.5 ; DRY RUN FEEDRATE SELECTED 选择了空运转进给率 DB21.DBB24.6 ; FEEDRATE OVERRIDE FOR 选择了进给修调 RAPID TRAVERSE SELECTED 用于快移 DB21.DBB25.3 ; PROGRAM TEST SELECTED 选择了程序试验 DB21.DBB25.7 ; SKIP BLOCK SELECTED 选择了程序段跳过 DB21.DBB26.0 ; ---------------------------------------------------------------------- PLC--------->NCK ACTIVATE FIXED FEED 激活固定进给1,2,3,4 DB21.DBB29.1,2,3,4 ; SWITCH OFF WORKPIECE COUNTOR 关闭工件计数 DB21.DBB29.5 ; ACTIVATE CONTOUR HANDWHEEL 激活手轮1,2,3 DB21.DBB30.0,1,2 ; ------------------------------------------------------------------------- NCK--------->PLC EXECUTION FROM EXTERNAL SOURCE ACTIVE 从外部执行已激活 DB21.DBB32.0 ; M00/M01 ACTIVE M00/M01已激活 DB21.DBB32.5 ; REVOLUTIONAL FEEDRATE ACTIVE 每转进给率已激活 DB21.DBB33.2 ; HANDWHEEL OVERRIDE ACTIVE 手轮修调已激活 DB21.DBB33.3 ; BLOCK SEARCH ACTIVE 程序段检索已激活 DB21.DBB33.4 ; M02/M30 ACTIVE M02/M30 已激活 DB21.DBB33.5 ; TRANSFORMATION ACTIVE 传输已激活 DB21.DBB33.6 ; PROGRAM TEST ACTIVE 程序试验已激活 DB21.DBB33.7 ; PROGRAM STATUS 程序状态 RUNNING 程序在运行中 DB21.DBB35.0 ; WAITING 程序在等待中 DB21.DBB35.1 ; STOPPED 程序已被停止 DB21.DBB35.2 ; INTERRUPTED 程序被中断 DB21.DBB35.3 ; ABORTED 程序被放弃 DB21.DBB35.4 ; CHANNEL STATUS 通道状态 ACTICE 通道已激活 DB21.DBB35.5 ; INTERRUPTED 通道被中断 DB21.DBB35.6 ; RESET 通道被复位 DB21.DBB35.7 ; ALL AXES REQUIRING REFERENCE POINT 所有的轴被要求回零 DB21.DBB36.2 ; ALL AXES STATIONARY 所有的轴在停止中 DB21.DBB36.3 ; INTERRUPT PROCESSING ACTIVE 中断处理被激活 DB21.DBB36.4 ; CHANNEL READY FOR 通道准备 DB21.DBB36.5 ; NCK ALARM PRESENT NCK报警 DB21.DBB36.6 ; NCK ALARM WITH PROCESSING STOP NCK报警且处理器停止 DB21.DBB36.7 ; HANDWHEEL ACTIVE 1 手轮1已激活 DB21.DBB37.0 ; HANDWHEEL ACTIVE 2 手轮2已激活 DB21.DBB37.1 ; HANDWHEEL ACTIVE 3 手轮3已激活 DB21.DBB37.2 ; READ IN ENABLE IS IGNORED 读入使能被忽略 DB21.DBB37.6 ; STOP AT BLOCK END WITH SBL IS SUPPRESSED 在程序段结束停止 DB21.DBB37.7 ; 几何轴的状态信号（NCK------>PLC) 轴 1 (DBB40----DBB43) HANDWHEEL ACTIVE 手轮已激活 DB21.DBB40.0,1 ; TRAVERSE COMMAND +,- 移动指令+,- DB21.DBB40.6,7 ; ACTIVE MACHINE FUNCTION 已激活的机床功能 INC 增量 DB21.DBB41 ; 轴 2 (DBB46----DBB49) 轴 3 (DBB52----DBB55) ======================================================================== PLC------>NCK FEEDRATE OCERRIDE 进给率修调 DB31.DBB0 ; DRIVE TEST MOVEMENT ENABLE 驱动试移动使能 DB31.DBB1.0 ; ACKNOWL FIXED STOP REACHED 确认定位停已到达 DB31.DBB1.1 ; SENSOR FIXED STOP 传感器实现的定点停 DB31.DBB1.2 ; AXES/SPINDLE DISABLE 轴/主轴禁止 DB31.DBB1.3 ; FOLLOW UP MODE 跟踪状态 DB31.DBB1.4 ; POSITION MEASURING SYSTEM 1 位置测量系统 1 DB31.DBB1.5 ; POSITION MEASURING SYSTEM 2 位置测量系统 2 DB31.DBB1.6 ; OVERRIDE ACTIVE 激活倍率 DB31.DBB1.7 ; CONTROLER ENABLE 控制机使能 DB31.DBB2.1 ; DELETE DISTANCE TO GO/ 删除剩余距离 SPUINDLE RESET /主轴复位 DB31.DBB2.2 ; REFERENCE POINT VALUE 1,2,3,4 参考点值 DB31.DBB2.4,5,6,7 ; ACCEPT EXTERNAL ZO 接受外部 ZO DB31.DBB3.0 ; ENABLE TRAVEL TO FIXED STOP 允许移动到固定停 DB31.DBB3.1 ; ACTIVATE FIXED FEED 1 激活固定进给率 1 DB31.DBB3.2 ; ACTIVATE FIXED FEED 2 激活固定进给率 2 DB31.DBB3.3 ; ACTIVATE FIXED FEED 3 激活固定进给率 3 DB31.DBB3.4 ; ACTIVATE FIXED FEED 4 激活固定进给率 4 DB31.DBB3.5 ; VELOCITY/SPINDLE SPEED LIMITATION 轴速/主轴速限制 DB31.DBB3.6 ; ACTIVATE HANDWHEEL 激活手轮 DB31.DBB4.0,1 ; FEED STOP/SPINDLE STOP 进给停/主轴停 DB31.DBB4.3 ; TRAVERSE KEY DISABLE 禁止移动键 DB31.DBB4.4 ; RAPID TRAVERSE OVERRIDE 快移修调 DB31.DBB4.5 ; TRAVERSING KEY +,- 快移键 +,- DB31.DBB4.6,7 ; MACHINE FUNCTION INC 1 增量 1 DB31.DBB5.0 ; INC 10 增量 10 DB31.DBB5.1 ; INC 100 增量 100 DB31.DBB5.2 ; INC 1000 增量 1000 DB31.DBB5.3 ; INC 10000 增量 10000 DB31.DBB5.4 ; VAR INC 可变增量 DB31.DBB5.5 ; ALLOCATE NC AXIS TO CHANNEL 分配 NC 轴给通道 DB31.DBB8.0,1,2,3 ; REQUEST PLC AXIS/SPINDLE 要求PLC轴和主轴 DB31.DBB8.7 ; PARAMETER SET DEFINITION FROM NC DISABLE 不能从NC定义参数 DB31.DBB9.3 ; HARDWARE LIMIT SWITCH 硬件限位开关 - DB31.DBB12.0 ; + DB31.DBB12.1 ; 2ND SOFTWARE LIMIT SWITCH 第二软限位开关 - DB31.DBB12.2 ; + DB31.DBB12.3 ; DELAY REFERENCE POINT APPROACH 参考点靠近延时 DB31.DBB12.7 ; ACTUAL GEAR STAGE 实际齿轮档位 DB31.DBB16.0,1,2 ; GEAR HAS CHANGED OVER 换档完成 DB31.DBB16.3 ; RESYNCHRONIZE SPINDLE 2 同步主轴 2 DB31.DBB16.4 ; RESYNCHRONIZE SPINDLE 1 同步主轴 1 DB31.DBB16.5 ; NO MONITORING WHEN CHANGING GEAR 变档时没有监控 DB31.DBB16.6 ; DELETE S VALUE 删除 S 值 DB31.DBB16.7 ; FEEDRATE OVERRIDE F SPINDLE VALID 进给修调对主轴有效 DB31.DBB17.0 ; RESYNCHRONIZE SPINDLE AT POS.1 同步主轴在位置 1 DB31.DBB17.4 ; RESYNCHRONIZE SPINDLE AT POS.2 同步主轴在位置 2 DB31.DBB17.5 ; INVERT M03/M04 反转M03和M04 DB31.DBB17.6 ; OSCILLATION VIA PLC 通过PLC 摇摆 DB31.DBB18.4 ; OSCILLATING SPEED 摇摆速度 DB31.DBB18.5 ; SETPOINT ROT. DIRECT 设定点旋转方向 CW DB31.DBB18.6 ; CCW DB31.DBB18.7 ; SPINDLE OVERRIDE 主轴修调 DB31.DBB19 ; RAMP CHANGE OVER U/F MODE 斜坡变到U/F状态 DB31.DBB20.0 ; RAMP FUNCTION GENERATOR INTERFACE 斜坡发生器接口 DB31.DBB20.1 ; TORQUE LIMIT 2 扭矩限制 2 DB31.DBB20.2 ; SPEED SETPOINT SMOOTHING 速度设定点平滑 DB31.DBB20.3 ; DRIVE PARAMETER SET SELECTION 侍服参数设定选择 DB31.DBB21.0,1,2 ; MOTOR SELECTION 电机选择 DB31.DBB21.3,4 ; SELECTING MOTOR 选择电机 DB31.DBB21.5 ; CONTROLLER INTEGRATOR DISABLE 控制机综合禁止 DB31.DBB21.6 ; PULSE ENABLE 脉冲使能 DB31.DBB21.7 ; DESELECT SAFE VELOCITY 取消选定的安全 AND STANDSTILL 速度并停止 DB31.DBB22.0 ; DESELECT SAFE STANDSTILL 取消安全停顿 DB31.DBB22.1 ; SPEED LIMIT BIT VALUE 0 速度限制位值 0 DB31.DBB22.3 ; SPEED LIMIT BIT VALUE 1 速度限制位值 1 DB31.DBB22.4 ; TRANSMISSION OF BIT VALUE 0 位传输值 0 DB31.DBB23.0 ; TRANSMISSION OF BIT VALUE 1 位传输值 1 DB31.DBB23.1 ; TRANSMISSION OF BIT VALUE 2 位传输值 2 DB31.DBB23.2 ; ACTIVATE END POSITION PAIR 2 激活端点对 2 DB31.DBB23.5 ; ACTIVATE TEST STOP 激活试验停止 DB31.DBB23.7 ; MASTER/SLAVE ON 打开主/从关系 DB31.DBB24.7 ; ENABLE SLAVE AXIS OVERLAY 允许从动轴覆盖 DB31.DBB26.4 ; ENABL EMERGENCY RETRACTION 允许紧急回退 DB31.DBB26.7 ; SET REVERSAL POINT 设置反转点 DB31.DBB28.3 ; CHANGE REVERSAL POINT 改变反转点 DB31.DBB28.4 ; STOP AT NEXT REVERSAL POINT 在下一个反转点停 DB31.DBB28.5 ; STOP 停止 DB31.DBB28.6 ; PLC CHECKS AXIS PLC检查轴 DB31.DBB28.7 ; -------------------------------------------------------------------------- NCK------------>PLC SPINDLE/NO AXIS 主轴/不是侍服轴 DB31.DBB60.0 ; NCU LINK AXIS ACTIVE NCU连接轴已激活 DB31.DBB60.1 ; ENCODER LIMIT FREQUENCY EXCEEDED 1 编码器频率超过 1 DB31.DBB60.2 ; EXCEEDED 2 编码器频率超过 2 DB31.DBB60.3 ; POSITION REACHED STOP COARSE 位置到达 粗停 DB31.DBB60.6 ; POSITION REACHED STOP FINE 位置到达 精停 DB31.DBB60.7 ; TRAVEL REQUEST 移动申请 DB31.DBB61.0 ; AXIS READY 侍服轴准备 DB31.DBB61.2 ; FOLLOW UP MODE ACTIVE 跟踪状态起动 DB31.DBB61.3 ; AXIS/SPINDLE STATIONARY 轴/主轴没有旋转 DB31.DBB61.4 ; POSITION CONTROLLER ACTIVE 位置控制器起动 DB31.DBB61.5 ; SPEED CONTROLLER ACTIVE 速度控制器起动 DB31.DBB61.6 ; CURRENT CONTROLLER ACTIVE 电流控制器起动 DB31.DBB61.7 ; SOFTWARE CAMS ACTIVE 软凸轮起动 DB31.DBB62.0 ; REVOLUTIONAL FEEDRATE ACTIVE 每转进给率起动 DB31.DBB62.2 ; MEASUREMENT ACTIVE 测量起动 DB31.DBB62.3 ; ACTIVATE TRAVEL TO 激活移动到 FIXED STOP 固定点停 DB31.DBB62.4 ; FIXED STOP REACHED 固定点停到达 DB31.DBB62.5 ; HANDWHEEL ACTIVE 1 手轮激活 1 DB31.DBB64.0 ; 2 手轮激活 2 DB31.DBB64.1 ; 3 手轮激活 3 DB31.DBB64.2 ; TRAVERSE COMMAND - 负向移动指令 DB31.DBB64.6 ; + 正向移动指令 DB31.DBB64.7 ; INC 1 增量 1 DB31.DBB65.0 ; INC 10 增量 10 DB31.DBB65.1 ; INC 100 增量 100 DB31.DBB65.2 ; INC 1000 增量 1000 DB31.DBB65.3 ; INC 10000 增量 10000 DB31.DBB65.4 ; VAR.INC 可变增量值 DB31.DBB65.5 ; POSITIONING AXIS 轴定位 DB31.DBB76.5 ; INDEXING AXIS IN POSITION 指针轴到位 DB31.DBB76.6 ; ROTARY AXIS IN POSITION 旋转轴到位 DB31.DBB76.7 ; GEAR CHANGE OVER 变档结束 DB31.DBB82.3 ; SPEED LIMIT EXCEEDED 速度限制被超过 DB31.DBB83.0 ; SET SPEED LIMITED 设定速度被限制 DB31.DBB83.1 ; SET SPEED INCREASED 设定速度被增加 DB31.DBB83.2 ; SUPPORT AREA LIMITS VIOLATED 支持区域极限干涉 DB31.DBB83.4 ; SPINDLE IN SETPOINT RANGE 主轴在设定点范围内 DB31.DBB83.5 ; SPEED MONITORING 速度监控 DB31.DBB83.6 ; ACTUAL ROTAT.DIRECTION CW 实际旋转方向 CW DB31.DBB83.7 ; CONST. CUTTING SPEED ACTIVE 恒速切削起动 DB31.DBB84.0 ; SUG ACTIVE (砂轮恒线速) DB31.DBB84.1 ; SYNCHRONOUS MODE 同步状态 DB31.DBB84.4 ; ACTIVE SPINDLE OPERATING POSITIONING MODE 使主轴工作在位控状态 DB31.DBB84.5 ; OSCILLATION MODE 使主轴工作在摇摆状态 DB31.DBB84.6 ; CONTROL MODE 使主轴工作在控制状态 DB31.DBB84.7 ; ACTIVE DRIVE PARAMETER SET 激活伺服参数设定 DB31.DBB93.0,1,2 ; ACTIVE MOTOR A ,B 激活电机 A,B DB31.DBB93.3,4 ; DRIVE READY 驱动准备 DB31.DBB93.5 ; n CONTROLLER INTEGRATOR DISABLE 控制机综合禁止 DB31.DBB93.6 ; ENABLE PULSES 脉冲使能 DB31.DBB93.7 ; TEMPERATURE PREWARNING MOTOR 温度预报警 电机 DB31.DBB94.0 ; HEAT SINK 热交换器 DB31.DBB94.1 ; RAMP UP COMPLETE 斜坡上升完成 DB31.DBB94.2 ; ================================================================================== 按功能组合起来的部分重要信号表 急停 EMERGENCY STOP 急停 PLC-->NCK DB10.DBB56.1 EMERGENCY STOP active 急停回答 NCK-->PLC DB10.DBB106.1 准备 MCP 1 READY MCP1准备 NCK-->PLC DB10.DBB104.0 (READY) MCP 2 READY MCP2准备 NCK-->PLC DB10.DBB104.1 NCK CPU READY NCK CPU 准备 NCK-->PLC DB10.DBB104.7 MMC 2 CPU READY MMC2 CPU 准备 NCK-->PLC DB10.DBB108.1 MMC CPU READY MMC CPU 准备 NCK-->PLC DB10.DBB108.3 DRIVE READY 驱动准备 NCK-->PLC DB10.DBB108.6 NC READY NC准备 NCK-->PLC DB10.DBB108.7 MODE GROUP 1 READY 状态组 1准备 NCK-->PLC DB11.DBB6.3 2 DB11.DBB26.3 AXIS READY 1 轴准备 NCK-->PLC DB31.DBB61.2 2 DB32.DBB61.2 3 DB33.DBB61.2 4 DB34.DBB61.2 DRIVE READY 1号轴驱动准备 NCK-->PLC DB31.DBB93.5 2 DB32.DBB93.5 3 DB33.DBB93.5 4 DB34.DBB93.5 禁止 MODE CHANGE DISABLE 1 状态改变禁止 PLC-->NCK DB11.DBB0.4 (DISABLE) 2 DB11.DBB20.4 KEY DISABLE 键盘锁住 PLC-->MMC DB19.DBB0.2 MODE CHANGE DISABLE 状态改变禁止 PLC-->MMC DB19.DBB44.0 FEED DISABLE 进给禁止 PLC-->NCK DB21.DBB6.0 READY-IN DISABLE 读入禁止 PLC-->NCK DB21.DBB6.1 NC START DISABLE NC 起动禁止 PLC-->NCK DB21.DBB7.0 GEOMETRY AXIS 1 TRAVERSING KEY DISABLE 几何轴1移动键禁止 PLC-->NCK DB21.DBB12.4 2 DB21.DBB16.4 3 DB21.DBB20.4 ORIENTATION AXIS 1 TRAVERSING KEY DISABLE 定向轴1移动键禁止 PLC-->NCK DB21.DBB320.4 2 DB21.DBB324.4 3 DB21.DBB328.4 AXIS/SPINDLE DISABLE 轴/主轴禁止 PLC-->NCK DB31.DBB1.3 TRAVERING KEY DISABLE 移动键禁止 PLC-->NCK DB31.DBB4.4 PARAMETER SET FROM NC DISABLED 从NC 设定参数被禁止 PLC-->NCK DB31.DBB9.3 n CONTROLLER INTEGRATO DISABLE 控制机综合禁止 PLC-->NCK DB31.DBB21.6 使能 ENABLE PROTECTION ZONES 保护区使能 PLC-->NCK DB21.DBB1.1 (ENABLE) DRIVE TEST MOVEMENT ENABLE 驱动试验移动使能 PLC-->NCK DB31.DBB1.0 CONTROLLER ENABLE 控制机使能 PLC-->NCK DB31.DBB2.1 ENABLE TRAVEL TO FIXED STOP 移动到固定的停止使能 PLC-->NCK DB31.DBB3.1 PULSE ENABLE 脉冲使能 PLC-->NCK DB31.DBB21.7 ENABLE SLAVE AXIS OVERLAY 使能从动轴覆盖 PLC-->NCK DB31.DBB26.4 ENABLE EMERGENCY RETRACTION 使能紧急回退 PLC-->NCK DB31.DBB26.7 激活 (ACTIVATE) INC INPUT IN MODE INC 输入在状态组 GROUP AREA ACTIVE 范围被激活 PLC-->NCK DB10.DBB57.0 ACTIVATE DRF 激活 DRF PLC-->NCK DB21.DBB0.3 ACTIVATE SINGLE BLOCK 激活单段 PLC-->NCK DB21.DBB0.4 ACTIVATE M01 激活 M01 PLC-->NCK DB21.DBB0.5 ACTIVATE DRY RUN FEEDRATE 激活空运转进给率 PLC-->NCK DB21.DBB0.6 ACTIVATE REFERENCING 激活定基准点 PLC-->NCK DB21.DBB1.0 ACTIVATE PROGRAM TEST 激活程序试验 PLC-->NCK DB21.DBB1.7 RAPID TRAVERSE OVERRIDE ACTIVE 快移修调起作用 PLC-->NCK DB21.DBB6.6 FEEDRATE OVERRIDE ACTIVE 进给率修调起作用 PLC-->NCK DB21.DBB6.7 FEEDRATE OVERIDE 进给率修调 PLC-->NCK DB21.DBB4 RAPID TRAVERSE OVERRIDE 快移修调 PLC-->NCK DB21.DBB5 激活相对机床的保护区 DB21.DBB8,9 激活通道特性保护区 DB21.DBB10,11 ACTIVATE HANDWHEEL 对几何轴1 激活手轮 PLC-->NCK DB21.DBB12.0,1 2 DB21.DBB16.0,1 3 DB21.DBB20.0,1 ACTIVATE FIXED FEED 激活固定进给 PLC-->NCK DB21.DBB29.0,1,2,3 ACTIVATE CONTOUR HANDWHEEL 激活电子手轮 PLC-->NCK DB21.DBB30.0,1,2 ACTIVATE FIXED FEED 激活固定进给 1 PLC-->NCK DB31.DBB3.2,3,4,5 ACTIVATE END POSITION PAIR 2 激活第二对端点位置 PLC-->NCK DB31.DBB23.5 ACTIVATE TEST STOP 激活试验停止 PLC-->NCK DB31.DBB23.7 起动 (START) NC START NC 起动 PLC-->NCK DB21.DBB7.1 停止 (STOP) MODE GROUP 1 STOP 状态组停止 PLC-->NCK DB11.DBB0.5 2 DB11.DBB20.5 CLC STOP CLC 停止 PLC-->NCK DB21.DBB1.4 NC STOP TO BLOCK LIMIT NC 在限位块停 PLC-->NCK DB21.DBB7.2 NC STOP NC 停止 PLC-->NCK DB21.DBB7.3 NC STOP AXIS PLUS SPINDLE NC 停止轴和主轴 PLC-->NCK DB21.DBB7.4 GEOMETRY AXIS 1 FEED STOP 几何轴 1 进给停止 PLC-->NCK DB21.DBB12.3 2 2 DB21.DBB16.3 3 3 DB21.DBB20.3 ORIENTATION AXIS 1 FEED STOP 定向轴 1 进给停止 PLC-->NCK DB21.DBB320.3 2 DB21.DBB324.3 3 DB21.DBB328.3 SENSOR FIXED STOP 传感器固定停 PLC-->NCK DB31.DBB1.2 FEED STOP/SPINDLE STOP 进给停/主轴停 PLC-->NCK DB31.DBB4.3 STOP AT NEXT REVERSAL POINT 在下一个反转点停止 PLC-->NCK DB31.DBB28.5 STOP 停止 PLC-->NCK DB31.DBB28.6 DESELECT EXTERNAL STOP 取消外部停止 PLC-->NCK DB31.DBB32.2,3,4 报警 （ALARM） MMC TEMPERATURE LIMIT MMC 温度极限 MMC-->PLC DB10.DBB103.6 MMC101/102)BATTERY ALARM MMC 电池报警 MMC-->PLC DB10.DBB103.7 NCK ALARM PRESENT NCK 报警出现 NCK-->PLC DB10.DBB109.0 HEAT SINK TEMP ALARM 热交换器温度报警 NCK-->PLC DB10.DBB109.5 AIR TEMP ALARM 空气温度报警 NCK-->PLC DB10.DBB109.6 NCK BATTERY ALARM NCK 电池报警 NCK-->PLC DB10.DBB109.7 CHANNEL SPECIFIC NCK ALARM PRESENT 通道专用的NCK报警 NCK-->PLC DB21.DBB36.6 NCK ALARM WITH PROCESSING STOP PRESENT NCK 报警处理器停止 NCK-->PLC DB21.DBB36.7 SPEED LIMIT EXCEEDED 速度极限被超过 NCK-->PLC DB31.DBB83.0 SET SPEED LIMITED 设定速度被限制 NCK-->PLC DB31.DBB83.1 SET SPEED INCREASED 设定速度被增加 NCK-->PLC DB31.DBB83.2 SPEED WARNING THRESHOLD REACHED 速度警告极限到达 NCK-->PLC DB31.DBB98.5 ACCELERATION WARNING THRESHOLD REACHED 加速度警告极限到达 NCK-->PLC DB31.DBB98.6 倍率 FEEDRATE OVERRIDE 进给率修调 PLC-->NCK DB21.DBB4 (OVERRIDE) RAPID TRAVERSE OVERRIDE 快移修调 PLC-->NCK DB21.DBB5 见激活 ORIENTATION AXIS 1 RAPID TRAVERSE OVERRIDE 定向轴 1 快移修调 PLC-->NCK DB21.DBB320.5 2 DB21.DBB324.5 3 DB21.DBB328.5 复位 (RESET) MODE GROUP 1 RESET 状态组复位 PLC-->NCK DB11.DBB0.7 MODE GROUP 2 RESET 状态组复位 PLC-->NCK DB11.DBB20.7 ALL CHANNELS IN RESET 所有的通道在 NCK-->PLC DB11.DBB26.7 STATE 复位状态 NCK-->PLC DB11.DBB6.7 RESET 复位 PLC-->NCK DB21.DBB7.7 状态选择 状态组 1 (MODE) AUTOMATIC MODE 自动状态 PLC-->NCK DB11.DBB0.0 MDA MODE 手动数据输入状态 PLC-->NCK DB11.DBB0.1 JOG MODE 点动状态 PLC-->NCK DB11.DBB0.2 TEACH IN MODE 示教状态 PLC-->NCK DB11.DBB1.0 REF MODE 回参考点状态 PLC-->NCK DB11.DBB1.2 SINGLE BLOCK 单段状态 PLC-->NCK DB11.DBB1.6,7 INC MODE X1 增量状态 X1 PLC-->NCK DB11.DBB2.0 X10 X10 DB11.DBB2.1 X100 X100 DB11.DBB2.2 X1000 X1000 DB11.DBB2.3 X10000 X10000 DB11.DBB2.4 VAR INC 可变增量 PLC-->NCK DB11.DBB2.5 FOLLOW UP MODE 跟踪状态 PLC-->NCK DB31.DBB1.4 状态响应 状态组 1 MMC AUTOMATIC MODE 自动状态 MMC-->PLC DB11.DBB4.0 MDA MODE 手动数据输入状态 MMC-->PLC DB11.DBB4.1 JOG MODE 点动状态 MMC-->PLC DB11.DBB4.2 TEACH IN 示教状态 MMC-->PLC DB11.DBB5.0 REF MODE　　　　　　　　回参考点状态　　　　 MMC-->PLC DB11.DBB5.2 NCK AUTOMATIC MODE 自动状态 NCK-->PLC DB11.DBB6.0 MDA MODE 手动数据输入状态 NCK-->PLC DB11.DBB6.1 JOG MODE 点动状态 NCK-->PLC DB11.DBB6.2 TEACH IN 示教状态 NCK-->PLC DB11.DBB7.0 REF MODE　　　　　　　　回参考点状态　　　　 NCK-->PLC DB11.DBB7.2 FOLLOW UP MODE 跟踪状态 NCK-->PLC DB31.DBB61.3 程序状态 RUNNING 在运行中 NCK-->PLC DB21.DBB35.0 WAITING 在等待中 NCK-->PLC DB21.DBB35.1 STOPPED 在停止中 NCK-->PLC DB21.DBB35.2 INTERRUPTED 在中断中 NCK-->PLC DB21.DBB35.3 ABORTED 被放弃 NCK-->PLC DB21.DBB35.4 通道状态 ACTIVE 被激活 NCK-->PLC DB21.DBB35.5 INTERRUPTED 被中断 NCK-->PLC DB21.DBB35.6 RESET 被复位 NCK-->PLC DB21.DBB35.7 一般状态 ALL AXES STATIONARY 所有的轴都没旋转 NCK-->PLC DB21.DBB36.3 测量选择 POSITION MEASURING SYSTEM 1 选用内编码器作反馈 PLC-->NCK DB31.DBB1.5 POSITION MEASURING SYSTEM 2 选用独立设备作反馈 PLC-->NCK DB31.DBB1.6 主轴控制 Axis/spindle disable 禁止轴和主轴 PLC-->NCK DB31.DBX1.3 Velocity/spindle speed limitation 轴和主轴速度限制 PLC-->NCK DB31.DBX3.6 Feed stop/spindle stop 进给和主轴停止 PLC-->NCK DB31.DBX4.3 Actual gear stage 实际挡位 PLC-->NCK DB31.DBX16.2,1,0 Gear has changed over 换挡完成 PLC-->NCK DB31.DBX16.3 No n-monitoring when changing gear 换挡时不监控 PLC-->NCK DB31.DBX16.6 Feedrate override for spindle valid 进给倍率对主轴有效 PLC-->NCK DB31.DBX17.0 Invert M3/M4 反转M3/M4 PLC-->NCK DB31.DBX17.6 Oscillation via PLC 从PLC进行主轴摇摆 PLC-->NCK DB31.DBX18.4 Oscillation speed 摇摆速度 PLC-->NCK DB31.DBX18.5 Setpoint rot.direct 主轴旋转方向 PLC-->NCK DB31.DBX18.6 CW DB31.DBX18.7 CCW spindle override 主轴倍率 PLC-->NCK DB31.DBX19 Spindle /no axis 该轴是主轴 NCK-->PLC DB31.DBX60.0 Setpoint gear stage 实际挡位 NCK-->PLC DB31.DBX82.0,1,2 Gear change over 换挡完成 NCK-->PLC DB31.DBX82.3 Speed limit exceeded 速度超过极限值 NCK-->PLC DB31.DBX83.0 Actual rotat direction 实际旋转方向 NCK-->PLC DB31.DBX83.7 CW Active spindle operating mode 主轴工作状态 NCK-->PLC DB31.DBX84.4 同步 NCK-->PLC DB31.DBX84.5 定位 屏幕控制 Screen BRIGHT 使亮屏 PLC-->NCK DB19.DBX0.0 Screen darkening 使黑屏 PLC-->NCK DB19.DBX0.1