有坛友咨询加工样件程序示例，我这里找到一个上传供坛友参考！

1,。展示样件说明：

展示件加工程序说明.pdf

2.加工程序示例：

DEF STRING[16] _LAUFWERK="USB"

DEF STRING[30] _FOLDERNAME="CHINA_214/WAVE/"

DEF STRING[30] _NC_FILE=""

DEF STRING[65] _EXEC_STR

DEF STRING[1] _HOCH_KOMMA=" "

_HOCH_KOMMA[0]=34

WORKPIECE(,,,"BOX",0,0,-40,-80,0,0,120,40)

;

WORKPIECE(,,,"CYLINDER",0,0,-32,-80,46)

;***R26=ZAEHLER,WELCHES FORMENBAUPROG. ZULETZT AKTIV WAR***

R25=0 ; 1=SPRUNG,KEINE PGM AUSWAHL AKTIV / 0=AUTO SPRUNG

GROUP_BEGIN(0,"CASE",0,0)

STOPRE

IF R25==1 ; OHNE AUTO SPRUNG

R26=0 ; RUECKSETZEN AUTOSPRUNG BEI PROGRAMMSTART

ENDIF

IF R26==0

IF _NC_FILE == "" GOTOF _OHNE_NC

GOTOF _PGM001

ENDIF

ENDIF

_OHNE_NC:

If R26==0

R26=1

endif

_CASE_CALL:

STOPRE

IF R26 == 01 GOTO _PGM01

IF R26 == 02 GOTO _PGM02

IF R26 == 03 GOTO _PGM03

IF R26 == 04 GOTO _PGM04

IF R26 == (04+1) GOTO _PGM_FINISH

GOTOF _ERROR

STOPRE

GROUP_END(0,0)

GROUP_BEGIN(0,"SPRUNGMARKEN",0,0)

;|NC  PROGRAMMS START

;|NC  PROGRAMMS END

;|EXT PROGRAMMS START

_PGM01:

_EXEC_STR ="EXTCALL("<< _HOCH_KOMMA << _LAUFWERK <<":"<< _FOLDERNAME <<"01_ROUGH.mpf"<< _HOCH_KOMMA <<")"

GOTOF _R_CAL   ;

_PGM02:

_EXEC_STR ="EXTCALL("<< _HOCH_KOMMA << _LAUFWERK <<":"<< _FOLDERNAME <<"03_PRE_FINISHING_01.mpf"<< _HOCH_KOMMA <<")"

GOTOF _R_CAL   ;

_PGM03:

_EXEC_STR ="EXTCALL("<< _HOCH_KOMMA << _LAUFWERK <<":"<< _FOLDERNAME <<"03_PRE_FINISHING_02.mpf"<< _HOCH_KOMMA <<")"

GOTOF _R_CAL   ;

_PGM04:

_EXEC_STR ="EXTCALL("<< _HOCH_KOMMA << _LAUFWERK <<":"<< _FOLDERNAME <<"04_FINISHING.mpf"<< _HOCH_KOMMA <<")"

GOTOF _R_CAL   ;

;|EXT PROGRAMMS END

GROUP_END(0,0)

GROUP_BEGIN(0,"_R_CAL",0,0)

;|_R_CAL START

_R_CAL:

M01

STOPRE

EXECSTRING(_EXEC_STR)

STOPRE

R26=R26+1

STOPRE

GOTOB _CASE_CALL

_PGM_FINISH:

R26=0

MSG("PROGRAMM ENDE")

T0

M6

MSG("")

M30

;|_R_CAL END

GROUP_END(0,0)

GROUP_BEGIN(0,"Fehlermarke",0,0)

_ERROR:

MSG("R26 FALSCH")

M00

STOPRE

GOTOB _ERROR

GROUP_END(0,0)；