quote:以下是引用refercata在2011-10-18 08:57:14的发言：
各个文件的显示级别如下，看看能不能找到哦啊你们所需要的：
Machine.ini

[ACCESSLEVEL]
JOG_PRESET=7 ; Preset or Set actual value at mode JOG mode
JOG_HAND=7 ; Handweel at mode JOG
JOG_ANKRATZ=7 ; Scratch
JOG_INCREM=7 ; Set increment at mode JOG
JOG_SYNAKT=7 ; Synchron actions at mode JOG
JOG_V_ISTW=7 ; watch windows of Actual-values,
JOG_V_ZOOM=7 ; Zoom actual values at mode JOG
JOG_INCHMET=7 ; Switch inch/Metric at mode JOG
JOG_REPOS=7 ; Semiautomatic REPOS at mode JOG
REF_SISITEC=4 ; Commit safety integrated Ref.Point
MDI_PROGBE=7 ; Program control at MDI mode
MDI_HAND=7 ; Handweel at MDI mode
MDI_EDITOR=7 ; Edit program at MDI mode
MDI_ED_DAT=7 ; Editor funtions at MDI mode
MDI_V_ISTW=7 ; watch windows of Actual-values
MDI_V_ZOOM=7 ; Zoom actual values at MDI mode
MDI_SYNAKT=7 ; synchron actions at MDI mode
MDI_DATEI=4 ; File funtions at MDI mode
MDI_INCHMET=7 ; Switch inch/Metric at MDI AUTO_OVERST=7
AUTO_DRF=7 ; DRF at AUTO mode
AUTO_PROGBE=7 ; Program control at AUTO mode
AUTO_SASUCH=7 ; Blocksearch at AUTO mode
AUTO_HAND=7 ; Handweel at AUTO mode
AUTO_EDITOR=7 ; Edit program at Auto mode
AUTO_KORREK=7 ; Correct program at AUTO mode
AUTO_V_ISTW=7 ; watch windows of Actual-values,

AUTO_V_ZOOM=7 ; Zoom actual values at AUTO mode
AUTO_V_NCPR=7 ; Programm-overview at AUTO mode
AUTO_OP_NCPR=7 ; load + select Progam at AUTO mode
AUTO_ED_NCPR=7 ; Alter enable status of Prog at AUTO mode
AUTO_SYNAKT=7 ; synchron actions at AUTO mode
AUTO_INCHMET=7 ; Switch inch/Metric at AUTO mode
AUTO_REPOS=7 ; Semiautomatic REPOS at mode AUTO
; access right to cycle directories
ENABLE_CMADIR=7
ENABLE_CUSDIR=7
ENABLE_CSTDIR=7

dg.ini

[ACCESSLEVEL]
ALARMS=7 ;Alarme
SERVICE=7 ;Serviceanzeigen"
COMMUNIC-LOG=3 ;Komm.- protokoll
PLC=7 ;Plc-Status
PLC-CHANGE=2 ;PLC-Status :
PLC-SYMBOLE=7 ;PLC-Symbol Status
;Sk-Change Value(Aendern) Sk-Reset Value (Aenderung Rueckgaengig)
;Sk-Commit Value (Aenderung uebernehmen) verriegelt ueber Hersteller
REMOTE=4 ;Ferndiagnose (RemoteDiagnosis)
FILE=7 ;Dateifunktionen
RUN-LOG=7 ;Sk-Fahrtenschreiber verriegelt ueber Anwender

ib.ini

[ACCESSLEVEL]
RESET =2 ;NCK-Reset NCK-Reset
CHG_SCL_SYS=5 ;change scaling system Masssystem inch/metrisch
MASCHDAT =4 ;Machine data Maschinendaten
DRIVE_CFG=2 ;drive configuration Antriebskonfiguratin
BOOTFILE=2 ;Bootfile Bootfile
MOT_CTRL=2 ;Motor/Valve selection Motor/Ventilauswahl
VIEW=2 ;Userviews + Displayoptions Anwendersichten u. Anzeigeoptionen
NC_ADDR=2 ;NCK Adress NCK Adress
SETUP_SWITCH=2 ;start-up switch IBN-Schalter
PLC_STATE=7 ;plc state PLC-Status
PLC_DATE=3 ;plc date PLC-Datum
PLC-CHANGE=2 ;PLC-Status :

DRIVE_SERVO=2 ;Drives/Servo Antriebe-Servo
SET_COL=3 ;colours Farben
SYST_SETTINGS=4 ;system settings Systemeinstellungen
SET_LANG=2 ;Language Sprachen
SET_BTSS=2 ;Operator panel Bedientafel
OPTION=2 ;Options Optionen
EDIT=1 ;Editor Editor
DOS=1 ;DOS shell DOS-Shell
TOOL_MNG=3 ;tool management Werkzeug- verwaltung
FILE=7 ;File functions Dateifunktionen
PASSWD=3 ;Set/Delete password Kennwort 鋘dern u. l鰏chen
CHG_PASSWD=7 ;SK "password ..." SK "Kennwort ..."

---